Welcome to TP-LINK Tech Support Forum
+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 15 of 23
  1. #1

    110 and 130 Bulbs dropping / losing connnection

    Model :

    Hardware Version :

    Firmware Version :

    ISP : [/COLOR]

    I have three LB130s and two LB110 bulbs set up in hard-wired light fixtures, connected via a Netgear Nighthawk AC1900 running current firmware. I am having constant disconnect problems with both bulb models, with disconnects sometimes happening within just a few minutes. The only way to bring the bulbs back online is to remove and reapply power; they'll power on (and light up), within a minute or so they'll be back online.

    I've spent the better part of a week trying different things to attempt to keep the devices online, all without success:
    1. Verified firmware is up to do using Kasa.
    2. Confirmed firewall rules allow outbound access.
    3. Set 2.4GHz access point to "failsafe" settings (RTS/CTS settings, Fragmentation)
    4. Changed 2.4GHz wireless to different channels (1, 3, 6, 7, 9, 11) to attempt to eliminate the possibility of interference.
    5. Relocated my wireless AP to ensure clear line-of-sight to all bulbs.
    6. Set DHCP reservations for the bulbs.
    Symptoms:
    • Devices appear offline (grayed out) in Kasa.
    • Bulbs remain in operating state when they lose their connection (if on, they stay on; if off, they stay off)
    • Unable to control devices in Kasa - device offline or out of range error.
    • Bulbs do not respond to 'ping.'
    • Bulbs come online - every time - perfectly after power cycle.
    My feeling is that the bulbs are either going to sleep or otherwise failing a "keep-alive." I'm running a constant 'ping' from my desktop to see if that helps keep the bulbs online. Anyone seen this? Anyone have a solution? (TP-Link - perhaps a firmware problem?)

  2. #2
    kalmairn - Have you found a resolution to your issue? I'm having the same problem with a new set of LB110's, the connection drops after [usually] a couple hours.

  3. #3
    Junior Member atavakoli is on a distinguished road
    Join Date
    Jan 2017
    Posts
    2

    Me too!

    just got my first LB-120 yesterday. Every couple of hours it drops off the network (which has full strength at it's location). Then I restart the bulb and it's back again immediately.

  4. #4
    Junior Member atavakoli is on a distinguished road
    Join Date
    Jan 2017
    Posts
    2
    Same behavior with the LB-120 - drops off every couple of hours a perfectly strong network connection. Once i restart it, it reconnects immediately.

  5. #5
    I've not solved it, but I've learned a little bit along the way.
    • Our Cable Modem / Wireless AP supports both 5GHz and 2.4GHz. We have an old gaming laptop that only supports 2.4GHz B/G/N. I found that every time my son used that old laptop for online computer games the bulbs would disappear within a few minutes. By adding a 5GHz USB WiFi card, or by connecting by cable (hardwire - who does that anymore?), the bulbs would be much more reliable.
    • There are a lot of other wireless APs within range of our home. I moved our 2.4GHz band from channel 1 where it competed with 11 other APs, to channel 9, placing it between the less-crowded channels 6 and 11. That also increased reliability.
    • Finally, we a couple days where we had some internet reliability issues. Our cable service was dropping packets at random. The bulbs would drop fairly frequently
    In all cases, removing and re-applying power would solve the problem, however left on their own they'd never reconnect.

    What I've learned, and what others could think about when setting up and troubleshooting:
    1. The bulbs are very sensitive to losing "airtime" on the WiFi network. If you tend to use your WiFi for high-bandwidth (movies) or high-chatter (online games) services, the bulbs tend to be less reliable.
    2. The bulbs deal with interference poorly. If there is a lot of cross-talk between WiFi access points, the bulbs are more likely to drop.
    3. These bulbs have either limited, more likely no, reconnect capability. Once the bulbs drop, either from the WiFi or from Kasa, they seem to stay offline until they're reset.
    My ask of TP-Link is to address the last item, in particular. Even if the service disappears, the bulb should have a recovery option in some sort of retry that continues on some reasonable repeating timescale. It's also possible an update could help with sensitivity to signal loss or competition for airtime, probably a little harder and longer to implement but likely more effective in the long run.

  6. #6
    Junior Member jtwjr is on a distinguished road
    Join Date
    Jan 2017
    Posts
    1

    Losing connection

    I had my bulbs lose connection as well and here is one thing I found out. I was trying to use the bulbs with Alexa and the Dot could not control the bulbs. I would try to control the bulbs with my iPhone but it would say the device was offline. Now what I found out was I had the Kasa app open on my iPad as well and it was controlling the bulbs. Once I closed the iPad app the iPhone regained control of the bulbs and then Alexa was able to control the bulbs as well. When I have lost the bulbs they seem to reconnect on their own without me having to turn off power.

  7. #7
    Interesting. I opened up a support case with TP Link and they had me download a utility to patch the firmware on the bulbs. So far this has worked great, no bulbs have lost connectivity (knock on wood). I'd give this a try if you haven't already.
    Last edited by pman; 01-09-2017 at 22:28. Reason: Adding sentence

  8. #8
    Quote Originally Posted by pman View Post
    Interesting. I opened up a support case with TP Link and they had me download a utility to patch the firmware on the bulbs. So far this has worked great, no bulbs have lost connectivity (knock on wood). I'd give this a try if you haven't already.
    What utility patch did they send ? Was it a standard Firmware update , what version , and have you had any more issues since ?

  9. #9
    Upgrade tool (which works on lightbulbs, and WiFI plugs) can be found at:
    http://www.tp-link.com/us/faq-949.html , the download is http://static.tp-link.com/iotUpgradeTool_V1.0.zip

  10. #10
    Has the problem been resolved?

    I have recently purchased TP bulbs and I'm having exactly the same problem with the bulb dropping the WiFi regularly. Router power cycle always reconnects it.

    I'm in an email chat with TP but their first suggestion was to factory reset the bulb so I'm not sensing a positive outcome....

  11. #11
    After a recent update on my Asus router both my TP-Link 100 series lights and my TP-Link HS105 mini plugs have started losing connection.overnight. My HS110 plug and HS200 switch were not affected. I tried the suggestions in the thread with no change in the problem. I finally reconnected the troubled components again and in the router setup changed their assigned IP addresses from DHCP to static. The affected products have not dropped out for 5 days now. May be something for you to try if you experience a similar problem.

  12. #12
    I read the suggestions here but still I am facing the same issue my bulb got dropping around every 3-4 hours.

    Crucial UK Discount Codes, vouchers and promo codes

  13. #13
    Tried static IP address earlier this evening and sadly the WiFi has been dropped within a few hours.TP Link sent me a link to a new firmware when I said I had Virgin Media superhub 2 as there seems to be some compatibility issue; however new firmware did not fix either.Really losing the will, I'm rebooting router two or three times a day to reconnect the bulb and this takes nearly five minutes to boot.I have another call with TP Link tomorrow but don't hold out too much hope.

  14. #14
    Hello All, I have been using the TP-Link Smart WiFi LED Bulb's & TP-Link HS100 Wireless Smart Plug's for some time now with very little problems at all while using my ADSL2+ internet connection. But in the last few weeks I upgraded to a home wireless 4G internet service and I needed a router with a sim card slot, so I purchased the TP-Link Archer MR200 Router as it had favourable feedback online.

    It didn't take long before I noticed some or all of my smart devices going offline sometimes 3-4 times a day and one that was only 90cm away from the router. I tried everything possible to make it work like resetting, relocating the router and even using WIFI extenders but nothing seemed to work. I even tried changing router settings like channels and channel width but still this didn't work. I called TP-Link tech support and after going through trouble shooting with them we agreed the router could be faulty and to return it for a replacement.

    Not giving up I decided to do some more research to see why some people lose WIFI signals at home and I found this article:
    https://www.howtogeek.com/171869/why...-connectivity/

    I tried it out by resetting the Smart Devices and making sure they were all online and working, then ran the microwave oven for about 20 seconds and when finished I asked my Google Mini to turn off the kitchen light and surprise it was offline, and even the Google Mini was struggling to answer me. Please keep in mind this is a $800 microwave that's only 2-3 years old so it's not like it's leaking because of bad seals or rust etc.

    I also read that one of the problems might be the smart devices IP address's changing and therefore disconnecting or losing the router connection, so I came across this too:
    https://www.tp-link.com/us/faq-1112.html

    First of all I went to my router settings and in my case as shown here https://www.tp-link.com/us/faq-1112.html (Advanced - Network - Lan Settings - Client list) I added all my Smart Bulbs, Smart Plugs and Google Mini's to the (Address Reservation) below my (Client List). This could be different if your using a different brand of router.

    These settings are for a 2.4GHz Connection, Not 5Ghz as TP-Link smart devices don't work on a 5GHz band as stated on the box.

    Next thing was (Advanced - Network - Internet)
    PDP Type: IPv4 & IPv6
    APN Type: Static
    Most other settings in this area were default to my ISP

    Next changes are:
    (Wireless - Wireless Settings)
    Security: WPA/WPA2 Personal
    Version: WPA2-PSK "Not Auto"
    Mode: 802.11n Only
    Channel: 11 Article also suggests Channels 1 & 6, but I've only tested channel 11 so far https://www.howtogeek.com/171869/why...-connectivity/
    Channel Width: 20MHz
    Transmit Power: High

    As from the time of this post it's been 24 hours since the changes and so far none of my smart devices have gone offline, even after running the microwave oven.
    I hope this works for you and good luck.
    Last edited by ShadowAD; 05-17-2018 at 14:08.

  15. #15
    I think it’s not entirely your fault. As a matter of fact the error in connection could be the result of many factors from defective product to obstructed signal. I would recommend you to try the product in direct line of sight just to make sure if it’s the signal. gokarna accommodation


 

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Copyright 1996-2018 TP-LINK Technologies Co., Ltd. All rights reserved.