Welcome to TP-LINK Tech Support Forum
+ Reply to Thread
Results 1 to 5 of 5
  1. #1
    Administrator tplink has disabled reputation
    Join Date
    Mar 2012

    Installation experiment of WBS210+TL-ANT2415MS

    TP-LINK Pharos series base station WBS210/WBS510 has no build-in antennas. Therefore an external antenna is needed for normal operation. To cooperate with WBS210 in PtMP scenario, ISP usually adopt assorting sector antenna TL-ANT2415MS to extend coverage area. In the following well learn how to install WBS210 on TL-ANT2415MS.

    Open the box of TL-ANT2415MS, we can see a smooth ripple surface, its the front panel of this antenna. In the backside there are electronic connectors for different uses, like below.
    Name:  l.jpg
Views: 0
Size:  206.7 KB

    With understanding of function for this connectors, we can start our installation.
    1. Firstly, attach the RF Cable to the Base station.
    2. Then attach the Base Station to the Base Station Mount Bracket.
    3. Next, connect the other ends of RF cable to the RF Connectors on the antenna.
    Name:  26.png
Views: 0
Size:  406.5 KB
    Its not recommended to connect the RF cable with connection type X since it may result in performance reduction.

    Then, we can continue the installation.
    4. Slide the Protective Shroud down over the Base Station until it locks onto the Base Station Mount Bracket.
    Name:  27.png
Views: 0
Size:  144.6 KB
    Till now, we have accomplished the connection and fixture of WBS210. In the following we need to install the whole antenna to the tripod.

    5. Attch the Antenna Mount Bracket to the four studs located on the antenna using the Flat Washers, Spring Washers, and Hex Nuts.
    Name:  28.png
Views: 0
Size:  320.8 KB

    6. Attach the Adjustable Pole-mount Bracket and Pole-mount Clamps to the pole using four M8X85 Bolts with Nut and Lock Washer Assemblies.
    7. Mount the Antenna Mount Bracket to the Adjustable Pole-mount Bracket using two M6x35 Bolts with Nut and Lock Washer Assemblies. Please do not over-tighten these bolts and nuts to allow angle adjustment later.
    Name:  29.png
Views: 0
Size:  118.5 KB

    8.The last operation, adjust the desired elevation angle of the antenna using the scale marked on the Antenna Mount Bracket, and then tighten the bolt and nut assemblies.
    Name:  30.jpg
Views: 0
Size:  41.5 KB

  2. #2
    Hope this product 5.8 avaiable in my country. and have good price
    and please more info device spec
    Last edited by aditrodostress; 05-06-2016 at 05:01.

  3. #3
    Members R1D2 is on a distinguished road
    Join Date
    Dec 2015
    Great product, well done, TP-Link. I like it very much!

    We deployed one of these at our customer's side to cover an outdoor area in a PtMP setup. Assembly was straightforward, good concept!
    Photo shows antenna placement during tests of the WiFi coverage from different angles.

    Name:  IMG_WBS210_ANT2415MS.jpg
Views: 0
Size:  47.8 KB

    Some remarks:

    - The two M6x35 bolts for the pole-mount bracket are slightly too short with the washer (or the bracket too thick ), we needed to use M6x40 instead.

    - Customer asked for some anti-theft provision such as a mechanical lock - any change this could be added?
    Some people might even climb onto radio masts for this device, the stay ropes of the mast already disappeared!

    - [Sorry, confused this in original post with CPE210 and same software, have edited it]
    Bult-in spectrum analyzer on WBS210 correctly shows range 2412 to 2472 MHz, firmware is
    1.3.3 Build 20160705 Rel. 52453.
    However, spectrum analyzer on CPE210 shows range 2312 to 2712 MHz instead. Firmware version is the same as on WBS210.

    Currently testing WBS210 with
    TL-ANT2424B in a PtP setup with CPE210 client over long distance (just because I have a spare ANT2424 and I'm curious).
    Last edited by R1D2; 10-11-2016 at 21:19.

  4. #4
    nice work ....
    what is the pole-mount brand u used in photo number 6 and 7 please

  5. #5

    nice post

    Accidentally I have come across this site and here it shares the installation experiment of WBS210+TL-ANT2415MS. Good to see that you have shared it with corresponding screenshot and diagram associated with. It helps anyone to understand it easily.jefferson reserve bourbon


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Copyright 1996-2018 TP-LINK Technologies Co., Ltd. All rights reserved.