Welcome to TP-LINK Tech Support Forum
+ Reply to Thread
Results 1 to 6 of 6
  1. #1

    T1700G-28TQ port isolation

    Hi folks,

    I believe there is a bug in the port isolation web interface (Switching -> Port -> Port Isolation).

    I click on Edit, select the ports and Apply. On the Port Isolation List I see settings are applied, but I have no ways to modify it. I can add others, displays ok, but again cannot edit nor revert them.

    At this point when I click on Edit I should get few "Selected" and "Not Available" ports, but all are "Unselected".

    I've tried Opera, Firefox, Chrome and IE but still no way to edit or revert without a reboot.
    Tests were luckily done on unused ports so no harm was done, I'll reboot it tonight.

    Am I missing something here.

    Cheers

    Model : T1700G-28TQ
    Hardware Version : T1700G-28TQRev2
    Firmware Version : 2.0.1 Build 20170608 Rel.61525(s)
    Last edited by caiordo; 01-04-2018 at 11:54. Reason: added system details

  2. #2
    I tried to manage it using CLI via SSH, but:

    sw> enable
    sw# configure
    ----^
    Error: Bad Command
    Last edited by caiordo; 01-04-2018 at 17:55. Reason: fixed cli systax

  3. #3
    Via telnet i was able to set it up, but the web interface remain unusable.

    Cheers

  4. #4
    Members TPTHZ is on a distinguished road
    Join Date
    Aug 2017
    Posts
    150
    Quote Originally Posted by caiordo View Post
    Via telnet i was able to set it up, but the web interface remain unusable.

    Cheers
    In my opinion, there are something wrong with your configuration ,did you configure forward port?
    Now, could you confgure other function? Only port isolation will display error message?

  5. #5
    Yes, forward port were setup, in fact I could see (via ssh I could only look at settings, via telnet I could also set) all applied settings used by me to test.
    Other functions like LAGG, VLAN, Spanning ecc are working great from a while.

    ### Before web and telnet
    Name:  tplink-port-isolation-init.jpg
Views: 0
Size:  49.3 KB

    ### Edit
    Name:  tplink-port-isolation-edit.jpg
Views: 0
Size:  60.6 KB

    ### After settings are applied web and telnet show proper config changes, but Edit page is blank so I cannot undo or add anything else... well I could add, but blindly or having two tabs open:
    Name:  tplink-port-isolation-review.jpg
Views: 0
Size:  114.1 KB
    Attached Images  
    Last edited by caiordo; 01-16-2018 at 16:17. Reason: Changed images

  6. #6
    Members TPTHZ is on a distinguished road
    Join Date
    Aug 2017
    Posts
    150
    Quote Originally Posted by caiordo View Post
    Yes, forward port were setup, in fact I could see (via ssh I could only look at settings, via telnet I could also set) all applied settings used by me to test.
    Other functions like LAGG, VLAN, Spanning ecc are working great from a while.

    ### Before web and telnet


    ### Edit


    ### After settings are applied web and telnet show proper config changes, but Edit page is blank so I cannot undo or add anything else... well I could add, but blindly or having two tabs open:
    In my opinion, this is not bug, if you want modify this setting, you only need choose port and fowarded port again.


 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Copyright 1996-2018 TP-LINK Technologies Co., Ltd. All rights reserved.