Welcome to TP-LINK Tech Support Forum

Search:

Type: Posts; User: R1D2

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    2

    Uhm, the 169.254.0.0/16 IP range is allocated to...

    Uhm, the 169.254.0.0/16 IP range is allocated to the "link local block" according to RFC3927. Your systems get an address from this range by auto-configuration if there is no DHCP server running in...
  2. Schreiben wir mal in deutsch weiter, ist zu...

    Schreiben wir mal in deutsch weiter, ist zu umständlich, immer zu übersetzen.



    Metall. Allerdings baust Du damit ein Reflektor und je nachdem, wie dieser wirkt, kann er Störungen bis hin zur...
  3. Should be possible, but depends on a lot of...

    Should be possible, but depends on a lot of factors to consider such as setup, antenna alignment, possible interferences at your place (radar) and even the weather.



    It is quite helpful if you...
  4. Yes, CPE510 would certainly fit, too. How did you...

    Yes, CPE510 would certainly fit, too. How did you measure the 2.9km?



    Good line of sight, which is most important.



    WBS510: up to 15km with sector antenna, up to 50km with dish antenna...
  5. Bugs in Pharos Control software for Linux (including a fix!)

    Here is an updated list of bugs in the Linux edition of Pharos Control, including a serious security-related bug. All bugs are related to missing privilege separation.

    That's the bad news....
  6. HOW-TO: Adding privilege separation to Pharos Control

    For all of you fellow UNIX/Linux admins who are concerned about security (and you should be concerned as an admin!), here is a short recipe on how to add privilege separation to your Pharos Control...
  7. Replies
    11
    Views
    12

    Definitely, a fixed IP will made things easier. :)

    Definitely, a fixed IP will made things easier. :)
  8. Replies
    7
    Views
    8

    Then the EAP330 with band steering and antenna...

    Then the EAP330 with band steering and antenna beamforming would be the right choice to support as much as 50 to 60 clients simultaneously, maybe even more.
  9. Replies
    2
    Views
    3

    You have to supply the password of the EAP to...

    You have to supply the password of the EAP to adopt the device, not the password of the EAP controller.
  10. Yes, it's pretty fast. Did you try ENTER/RETURN...

    Yes, it's pretty fast. Did you try ENTER/RETURN on a SmartPhone? Probably it depends on the browser/event, didn't investigate this further.
  11. Great! But there is a bug in the control.sh...

    Great!

    But there is a bug in the control.sh start/stop script: it creates a logfile "stop.log" in the bin subdirectory instead of in the logs directory if the Controller is stopped. Probably...
  12. Replies
    7
    Views
    8

    Perfectly answered by winstar. No, I would not...

    Perfectly answered by winstar.

    No, I would not just recommend 10 EAPs without having measured the effects of installing more then 4 devices in the room b/c of congestion of the 2.4 GHz band....
  13. Replies
    7
    Views
    8

    I would use a bunch of EAP320/EAP330 with high...

    I would use a bunch of EAP320/EAP330 with high wireless throughput in order to provide AirTIme to as much people as possible. In theory, you would need at least 8 or so EAPs to handle 400 clients,...
  14. What says the built-in speed test if you test...

    What says the built-in speed test if you test pure wireless speed between the two WBS?



    Kaufen kannst immer alles. Use a cable such as the TL-ANT24EC5S, which has an attenuation of 4.5dBm, and...
  15. Yes. The hyperlink antenna isn't a MIMO antenna...

    Yes. The hyperlink antenna isn't a MIMO antenna (requires a dual polarized antenna) and electrical characteristics can differ, too.

    As for your wireless settings:

    Set channel width to 20 MHz....
  16. Replies
    3
    Views
    4

    I see. Much of the confusion here is about...

    I see. Much of the confusion here is about terminology: a router isn't an AP and client isolation isn't the same as a client's network separation. I think, tech support can help you to find the right...
  17. Contact TP-Link support (ticket.tp-link.com). ...

    Contact TP-Link support (ticket.tp-link.com).



    That's just my opinion and setup in our lab: no DHCP. Doesn't improve preparation, but hinders it. Your mileage may vary.
  18. V2 software is just a Visual Identity update and...

    V2 software is just a Visual Identity update and rumors has it that V2 hardware will have only one Ethernet port and no more PoE pass-through. So I certainly prefer V1 hardware over the V2.



    In...
  19. I did sent you a PM.

    I did sent you a PM.
  20. It also would be helpful to have the EAPs sending...

    It also would be helpful to have the EAPs sending a heartbeat to an external portal/auth server, for example by letting the user specify an URL, which contains the MAC address of the EAP (such as...
  21. The EAP110 uses passive PoE (24 volts), too. Do...

    The EAP110 uses passive PoE (24 volts), too. Do not try to feed 48 volts standard PoE to it, it could break your unit.
  22. Replies
    3
    Views
    4

    I don't know any AP which offers an isolated...

    I don't know any AP which offers an isolated guest network and a firewall. A WiFi router does all this stuff and those devices usually offer isolated guest networks, subnets and a firewall.

    But...
  23. Replies
    1
    Views
    2

    Yes, you can set up a guest network w/o portal...

    Yes, you can set up a guest network w/o portal and with client isolation, but since the EAP is an AP only (not a router!) it just offers functionality to create several SSIDs (one of it you could...
  24. Replies
    1
    Views
    2

    The TL-SG1024DE is a Layer-2 switch. You can't...

    The TL-SG1024DE is a Layer-2 switch. You can't assign IPs to networks on L2 switches. The IPs must be either set statically on all connected devices or you can use a DHCP server to have it...
  25. Thread: Set up TL-SG108E

    by R1D2
    Replies
    1
    Views
    2

    For most people the switch works as just...

    For most people the switch works as just plug-and-play. But if your network uses IPs in the 192.168.0.x range, you need to configure the IP of the switch, which is by default 192.168.0.1.

    It's...
Results 1 to 25 of 118
Page 1 of 5 1 2 3 4

Copyright © 1996-2017 TP-LINK Technologies Co., Ltd. All rights reserved.