Welcome to TP-LINK Tech Support Forum

Search:

Type: Posts; User: R1D2

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    4

    dnsmasq won't help at all and ipset isn't needed...

    dnsmasq won't help at all and ipset isn't needed to set rules for allowing access to certain IP addresses. But there are other problems such as distinguishing between authentication and normal...
  2. Replies
    17
    Views
    18

    Sure, no problem. Find attached archive of all 7...

    Sure, no problem. Find attached archive of all 7 partitions. But take care to flash them on correct addresses. When I last checked the OpenWRT partition table, it was different compared to the...
  3. I now reverted settings in the opposite order:...

    I now reverted settings in the opposite order: first enabled AP isolation and set no encryption on bridge and then on AP. Interestingly, AP changed the channel from 112 to 124 and bridge did not...
  4. Disabled AP Isolation and set WPA2 key with AES...

    Disabled AP Isolation and set WPA2 key with AES encryption on main AP at 23:11:22 and bridge at 23:13:15. Bridge did re-connect almost immediately after I applied/saved the config; exactly at...
  5. Maybe later at night. It's in use and we need...

    Maybe later at night. It's in use and we need open access to this AP during the day.

    Meanwhile, my bridge CPE did re-connect to the main AP automatically after another reboot of the main AP, but...
  6. Works for me. But you have to set up the SMTP...

    Works for me. But you have to set up the SMTP server correctly. The CPE needs plain authentication (or none at all, but beware of bogus HELO message then) and it can not use TLS encrypted mail...
  7. Hm, works flawlessly this time. This is what I...

    Hm, works flawlessly this time. This is what I have done:

    Set static IP, system time, bridge mode. Leave AP enabled, turned AP isolation on. Did a survey, locked to AP. Connected on first attempt...
  8. Yes, but note that for the tests in #6 I had...

    Yes, but note that for the tests in #6 I had differing WiFi settings. I had AP isolation enabled on main AP and disabled on the bridge's AP. Then I disabled everything (even the bridge's AP at all)...
  9. Enable ssh access on the CPE in menu Management...

    Enable ssh access on the CPE in menu Management and just use an ssh client to enter following command on the command line (replace the IP address and the admin password by the ones you are using):
    ...
  10. Definitely yes. PharOS lets you choose...

    Definitely yes.



    PharOS lets you choose almost any setting possible, it's a business-class device for power users. Choosing meaningful options for a robust network topology is up to the user.
    ...
  11. Replies
    1
    Views
    2

    Sure. Just set a static (fixed) IP address for...

    Sure. Just set a static (fixed) IP address for the EAPs using the built-in web-UI. See the manual for the EAP how to do this.
  12. Replies
    3
    Views
    4

    Menu System -> LED in EAP-Controller. You can...

    Menu System -> LED in EAP-Controller. You can turn the LED on/off for the whole site, not for a single device.

    Did you RTFM meanwhile? The Controller has an own manual:...
  13. Replies
    2
    Views
    3

    Set the Thompson to static IP 10.0.0.1 and the...

    Set the Thompson to static IP 10.0.0.1 and the CPE to static IP 10.0.0.2. Gateway for the CPE is the Thompson, 10.0.0.1.

    Set DHCP first address 10.0.0.10, last address to what you need, e.g....
  14. According to this article:...

    According to this article: http://forum.tp-link.com/showthread.php?84173-VLAN-transfer-and-management-VLAN-introduction PharOS passes VLAN tags from remote LAN to local LAN.

    Are you sure that the...
  15. Replies
    3
    Views
    4

    Yes, they can be controlled by the same EAP...

    Yes, they can be controlled by the same EAP controller.
  16. Replies
    3
    Views
    4

    EAPs are Thin APs, not universal hotspot...

    EAPs are Thin APs, not universal hotspot gateways. You need EAPs in order to use their portal functions.
  17. Replies
    3
    Views
    4

    You can either adopt an EAP and use the EAP...

    You can either adopt an EAP and use the EAP Controller (EAC) to control EAP settings exclusively or you can use the EAP in standalone mode, but then you can't use EAC. Therefore local settings such...
  18. Replies
    3
    Views
    4

    You need to open the EAPs for client access to...

    You need to open the EAPs for client access to those auth services, for example with a free authentication policy in EAC. But it's no ideal solution: if IPs change, you have to change the ACL rules,...
  19. I'm not sure I understand you correctly regarding...

    I'm not sure I understand you correctly regarding setup challenge, but I meant the HNP is most certainly the cause for the disruption of the link between CPE#1 and CPE#2 if you change something at...
  20. V1 hardware of this switch has no web UI. The web...

    V1 hardware of this switch has no web UI. The web UI was introduced with hardware V2.

    If you got an error during upgrade, it means that you tried to update wrong firmware image. If you see the...
  21. O.k., then I am pretty sure that your setup hits...

    O.k., then I am pretty sure that your setup hits the hidden node problem.

    Either change the roles (CPE#1 in client mode <---> CPE#2 in AP mode <---> CPE#3 in client mode), so you can use MAXtream...
  22. The main AP's SSID to which the bridge connects....

    The main AP's SSID to which the bridge connects. If I change the bridge AP's SSID, this has no effect on the link to the main CPE, it remains connected.



    As far as I understand you have...
  23. Same findings: Disabled MAXtream on main AP,...

    Same findings:

    Disabled MAXtream on main AP, set to fixed channel 100. Apply, save config, reboot.
    Enabled AP on bridge CPE. Apply, save config, reboot. Connected immediately.

    First test:...
  24. Yes, don't hurry. Tests are in progress and they...

    Yes, don't hurry. Tests are in progress and they need time. I'm testing next without MAXtream.
  25. The Test with DFS enabled again is done also. So...

    The Test with DFS enabled again is done also. So far it seems that the DFS setting for channel selection seems to be the critical parameter. I also double checked that each and every wireless setting...
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4

Copyright 1996-2017 TP-LINK Technologies Co., Ltd. All rights reserved.