Welcome to TP-LINK Tech Support Forum

Search:

Type: Posts; User: Victor Ramos

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. No ... it refers to an IP that is not in use in...

    No ... it refers to an IP that is not in use in the network, it can not be the IP of the main router, nor the IP of any static device like any other AP, or camera or dvr ... nor any IP that is...
  2. Replies
    27
    Views
    28

    Apology R1D2 .... I made a long time ago a...

    Apology R1D2 ....


    I made a long time ago a modification to a CPE210 and an old router removed the antenna cables with RPSMA connectors, and the PharOS CPE210 I could connect two small...
  3. Replies
    3
    Views
    4

    I already explained it @Lymay ... the TL-WA7510...

    I already explained it @Lymay ... the TL-WA7510 is a device that works in 5.8GHz ... (as a saying goes ... A GOOD UNDERSTANDING ... few words ....)


    you are wanting to see a signal on that...
  4. Replies
    6
    Views
    7

    If you are able, you will be able to find the way...

    If you are able, you will be able to find the way ... sometimes not everything is written ... estro I published it in a forum on networks for WISP, and recovers a 7510 with infinite boot ....

    ...
  5. Replies
    6
    Views
    7

    1.9km, you are very limited, since you are not...

    1.9km, you are very limited, since you are not your country and the regulations of power ..., but for that distance with maximum power, in particular tests of mine, it is just what allows a decent...
  6. Replies
    6
    Views
    7

    The requirement for a wireless connection is that...

    The requirement for a wireless connection is that there must be at all times line of sight or LoS, it means that the equipment must be seen among themselves and be higher than the obstacle in a...
  7. Replies
    6
    Views
    7

    This could be a BOOT INFINITY problem... You...

    This could be a BOOT INFINITY problem...

    You could try to connect to the 7210 by TELNET through PUTTY utility ... to the default ip 192.168.1.254, of course you must reset to factory values 7210...
  8. Replies
    40
    Views
    41

    Very Well Said... Let's not make the radio...

    Very Well Said... Let's not make the radio spectrum a garbage dump

    Regards...
  9. Replies
    10
    Views
    11

    Jajajajajajajaj ..... with due pardon for the...

    Jajajajajajajaj ..... with due pardon for the sarcasm .... but before recommending something, I should first investigate how these devices work, and not throw a comment of that magnitude just by the...
  10. Matt, before you buy, I think you should...

    Matt, before you buy, I think you should determine what killed your CPE210 ... because a third unit could go through it ...

    If it were humidity, you could solve it by placing the CPE in a...
  11. Of everything that you have answered, there is...

    Of everything that you have answered, there is only something that is not clear to me and it is with respect to the system of electrical protection ... and I ask again ...




    -have in the...
  12. Hi Matt... Long time ago I collaborate with...

    Hi Matt...

    Long time ago I collaborate with you to solve your connection problem there in the jungle ...


    Regarding your concerns, I will tell you that first you have to determine which part...
  13. Thread: No PoE

    by Victor Ramos
    Replies
    2
    Views
    3

    it's possible... To discard this you could...

    it's possible...


    To discard this you could try connecting another PoE adapter, or check with a multitester the output voltage with a cable tail connected to the port marked with PoE of the...
  14. Replies
    2
    Views
    3

    This part is universal for all wireless...

    This part is universal for all wireless connection, the radios must speak the same language, each channel is a different language ....


    The correct configuration would be ...


    CPE210 AP MODE...
  15. is correct... An IP outside the DHCP range of...

    is correct...

    An IP outside the DHCP range of the main router and other than the IP and gateway of the same to avoid some conflict ...

    Regards
  16. That is because the WEP protocol is very...

    That is because the WEP protocol is very insecure, and the new devices no longer allow to implement it, as a recommendation you should change the security of the entire network ...

    Regards...
  17. Replies
    7
    Views
    8

    No problem ... enjoy your trip Regards...

    No problem ... enjoy your trip

    Regards...
  18. Replies
    2
    Views
    3

    if possible. But I must remind you that the...

    if possible. But I must remind you that the direct coverage from the point of origin, could result in a signal low inside the house, since the signal would not cross the walls very well, resulting in...
  19. Replies
    7
    Views
    8

    1.- Try configuring it in the DNS box by placing...

    1.- Try configuring it in the DNS box by placing the same IP of the Gateway ... 192.168.0.253 ...

    2.- In WIRELESS CONNECTION, the signal strength is very bad ... -75 ... should get better signal...
  20. The station refers to the equipment that receives...

    The station refers to the equipment that receives the signal at the other end ...


    You must also publish the connection details on the device to connect .. ejm a laptop or desktop pc ... what...
  21. Replies
    7
    Views
    8

    Missing a bit more information... You could...

    Missing a bit more information...


    You could place a screenshot of the main and network tab of the 210, to see the connection values ... And details the connection on your device when you...
  22. Perfect ... I have already published information...

    Perfect ... I have already published information from the AP .... now the data of the station is missing...

    Regards...
  23. Replies
    7
    Views
    8

    You must configure the 210 not as repeater, if...

    You must configure the 210 not as repeater, if not as AP client router ... and wireless AP disabled ... to use it only as client router ... here will connect to the park AP in automatic dhcp mode...
  24. For the 2km it publishes we are a little to the...

    For the 2km it publishes we are a little to the real limit of the connection distance of that equipment with the use of a standard sector antenna ... this changes with the use of directional antenna...
  25. Replies
    6
    Views
    7

    So that they are in another different subnet...

    So that they are in another different subnet should set the CPE210s in AP Client Router ...
    This video explanatory, (I did not find something in the knowledge base)
    ...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4

Copyright 1996-2017 TP-LINK Technologies Co., Ltd. All rights reserved.